MG3710A


MG3710A MG3710A MG3710A
MG3710A
MG3710A
MG3710A
MG3710A

The MG3710A Vector Signal Generator is a best-of-class, high-function, signal generator with excellent RF and baseband performance. It is a vector signal generator with 6-GHz upper frequency limit and 160-MHz*/ 120-MHz wide RF modulation baseband generator. It outputs various radio systems signals for cellular communications, such as LTE FDD/TDD, W-CDMA, GSM as well as narrowband communications, such as WLAN, WiMAX™, Bluetooth™ and GPS.

* with option MX370111A WLAN IQproducer™ and MX370111A-002 802.11ac (160 MHz) only.

Dual RF Output & Dual Waveform Memory

mg3710a_dualrf

The MG3710A supports two separate built-in RF outputs (option). The frequency can be selected from 2.7/4.0/6.0 GHz. The two RF outputs can be set to different frequencies, levels and waveform data/CW. As a result, there is no need for two expensive vector signal generators.

The built-in signal generator function outputs both continuous wave (CW) and modulated signals for use as a reference signal source when testing Tx characteristics of parts and as a signal source for evaluating Rx characteristics.


mg3710a_dualwave

For example: Wanted + Interference Signal, Wanted + Delayed Signal, and Wanted Signal of Different Sampling Rate

SSB Phase Noise Performance

mg3710a_SSB

< -140 dBc/Hz (nom.) @ 100 MHz, 20 kHz offset, CW
< -131 dBc/Hz (typ.) @ 1 GHz, 20 kHz offset, CW
< -125 dBc/Hz (typ.) @ 2 GHz, 20 kHz offset, CW

SSB phase noise is an important performance index for signal generators.

For example, when using a signal generator for the following purposes, it is important to pre-confirm that the signal generator performance satisfies the measurement specifications.

  • Communications with narrow bandwidth of several kHz
  • OFDM Signals with narrow subcarrier gap
  • CW interference waveforms

Top-class ACLR Performance: -71 dBc @ W-CDMA, TestModel1, 64DPCH, 2 GHz

Top-class ACLR performance supports measurement closer to the DUT's original ACLR performance. High ACLR performance increases margin specifications and improves measurement stability and yield.

For example: Evaluation of base station amplifiers, etc., requires excellent adjacent channel leakage power (ACLR) performance. Normally, the signal from the vector signal generator is inserted to an amplifier, and the amplifier output signal ACLR characteristics, etc., are measured with a spectrum analyzer. Instruments for these measurements require high ACLR performance.


mg3710a_ACLR

High Level Accuracy

mg3710a_accuracy

Absolute Level Accuracy: ±0.5 dB *1
Linearity: ±0.2 dB (typ.) *2

Excellent level accuracy and linearity are key factors with a large impact on measurement accuracy.


*1 400MHz to 3GHz, -110 to +10 dBm
*2 50 MHz to 3GHz, -110 to -1 dBm

Fast Switching Speed: < 600us (List/Sweep Mode)

The MG3710A supports high-speed switching in the sweep and list mode separately from normal remote control. It is ideal for production lines requiring short test times.

Sweep Mode

List Mode

In Sweep mode, the dwell time per point or number of points is split between the frequency range and level range (Start/Stop). This mode is used when matching dwell time per point and frequency / level steps.


In List mode, the frequency, level and dwell time can be set for each of up to 500 points. This mode is used when wanting to set any dwell time, and frequency / level step per point.


mg3710a_sweep
mg3710a_list

Low Power and High Power Output Extension

Assured Maximum Output Power Level (CW):

Frequency Range Standard Opt. 041 / 071
100 kHz to 10 MHz +5 dBm +5 dBm
10 MHz to 50 MHz +10 dBm +10 dBm
50 MHz to 400 MHz +13 dBm +20 dBm
400 MHz to 3GHz +23 dBm
3 GHz to 4GHz +20 dBm
4 GHz to 5GHz +13 dBm
5 GHz to 6 GHz +11 dBm +11 dBm
mg3710a_max_power

In conventional measurement setup, path loss is increased by the various external components in the RF path. Thus, an external amp is required when the output of the general signal source is insufficient.

The MG3710A High Power Extension option*1 improves signals required for path loss compensation. It eliminates the cost of an external amp, supports stable level accuracy measurements and reduces risk of damage to the DUT from the external amp.


Amplitude Setting Range:

Options Setting Range (dBm)
without
Reverse Power Protection*3
with
Reverse Power Protection*3
Standard -110 to +17 -110 to +17
with High Power Extension -110 to +30 -110 to +25
with Low Power Extension -144 to +17 -144 to +17
with Low and High Power Extension -144 to +30 -144 to +25

On the other hand, the MG3710A also supports a convenient option for extending the lower RF output limit via Low Power Extension*2 option when performing high-sensitivity Rx tests.

*1 High Power Extension for 1st RF / 2nd RF [Opt.041 / 071]
*2 Low Power Extension for 1st RF / 2nd RF [Opt.042 / 072]
*3 Reverse Power Protection for 1st RF / 2nd RF [Opt.043 / 073]

Pre-installed and Optional Waveform Patterns

Waveform patterns for the world's main communications systems are pre-installed in the MG3710A for license-free use.

Pre-installed Waveform Patterns [License-free]

Optional Waveform Pattern [Optional License]

IQproducer™ Waveform Generation Software [Optional License]

LTE FDD (E-TM1.1 to E-TM3.3) DFS Radar Pattern (For TELEC & FCC) LTE FDD/LTE-Advanced FDD
LTE TDD (E-TM1.1 to E-TM3.3) DFS (ETSI) Waveform Pattern LTE TDD/LTE-Advanced TDD
W-CDMA/HSDPA ISDB-Tmm Waveform Pattern HSDPA/HSUPA/W-CDMA
GSM/EDGE TD-SCDMA
CDMA2000™ 1X/1xEV-DO CDMA2000™ 1xEV-DO
Bluetooth™, GPS, PDC, PHS Mobile WiMAX™
Digital Broadcast (ISDB-T/BS/CS/CATV) WLAN 11a/b/g/n/j/p/ac
WLAN (IEEE802.11a/11b/11g) TDMA (PDC, PHS, Public Radio System.)
DVB-T/H
Multi-carrier
Fading

Basic Performance

Parameters / Characteristics Specifications
Frequency Frequency Range 9 kHz to 2.7 GHz (MG3710A-032/062)
9 kHz to 4 GHz (MG3710A-034/064)
9 kHz to 6 GHz (MG3710A-036/066)
Resolution 0.01 Hz
Output Level Output Range Without reverse power protection
   -110 to +17 dBm (standard)
   -110 to +30 dBm (with high power extension option)
   -144 to +17 dBm (with low power extension option)
   -144 to +30 dBm (with high power extension and low power extension option)
Resolution 0.01 dB
Difference of CW and MOD Based on 5 MHz bandwidth AWGN signal, at 18 to 28°C, output level < +1 dBm
±0.2 dB (98 MHz ≤ f &le 6 GHz)
Accuracy CW, +18° to +28°C, , -100 to +5 dBm, without reverse power protection
   ±0.5 dB typ. (100 kHz ≤ f < 50 MHz)
   ±0.5 dB     (50 MHz ≤ f ≤ 3 GHz)
   ±0.7 dB     (3 GHz < f ≤ 4 GHz)
   ±0.8 dB     (4 GHz < f ≤ 6 GHz)
Signal Purity Spurious / Harmonics < -30 dBc
Spurious / Non-harmonics -30 dBm ≤ Output level ≤ +5 dBm, CW, &ge 10 kHz offset
   < -62 dBc, -70 dBc typ. (100 kHz ≤ f ≤ 187.5 MHz)
   < -68 dBc, -76 dBc typ. (187.5 MHz < f ≤ 750 MHz)
   < -62 dBc, -76 dBc typ. (750 MHz < f ≤ 1.5 GHz)
   < -56 dBc, -70 dBc typ. (1.5 GHz < f ≤ 3 GHz)
   < -50 dBc, -64 dBc typ. (3 GHz < f ≤ 6 GHz)
SSB Phase Noise CW, 20 kHz offset, Phase Noise Opt. < 200 kHz
   < -140 dBc/Hz nominal (100 MHz)
   < -131 dBc/Hz typ. (1 GHz)
   < -125 dBc/Hz typ. (2 GHz)
Arbitrary Function Generation DAC Resolution 14 bit, 15 bit, 16 bit
Sample Rate 20 kHz to 200 MHz* / 160 MHz

(* : Only when using MX370111A and MX370111A-002)

Waveform Memory 64 Msample (256 MB) [with 1stRF and 2ndRF]
256 Msample (1 GB)   [Opt-045/075]
1024 Msample (4 GB) [Opt-046/076]
Waveform Output Mode When Baseband Signal Combine Function [Opt-048/078] configured with two internal waveform memories and one waveform selected at each memory with level ratio (CN) set to 80 dB, and frequency offset set to ±60 MHz max. Supports signal output from either memory and both signals can be digitally combined internally for output.
  • Defined Mode: Set to combine two signals just by selecting configuration file
  • Edit Mode: Set manually to any two signal waveform patterns, level ratio, offset frequency, etc.
RF Modulation Bandwidth Using Internal Base-band Signal Generator 160 MHz* / 120 MHz

* Supports firmware version 2.00.00 and later. Only when using MX370111A and MX370111A-002.

Using External IQ Input 160 MHz
Dimensions and Mass 426 (W) x 177 (H) x 390 (D) mm (Exclusive surface projection)
≤13.7 kg (with Opt-032 or 034 or 036, excluding other options)
BER Measurement [Opt-021] Bit Rate 100 bps to 40 Mbps
Connector Rear AUX connector, TTL level
Measurable Patterns PN9/11/15/20/23, PN9fix/11fix/15fix/20fix/23fix, ALL0, ALL1, alternating 0 and 1, UserDefine
Remote Control Interface GPIB, 1000Base-T, USB-B
Waveform Option IQproducer™ PC software with simple GUI for setting parameters for any communications method and generating waveform patterns.
Supported systems (standard bundle):
  • W-CDMA IQproducer™, AWGN IQproducer™
Supported Systems (Separately Sold Licence*) [Model: MX3701xxA]:
  • MX370101A HSDPA/HSUPA IQproducer™
  • MX370102A TDMA IQproducer™
  • MX370102A TDMA IQproducer™
  • MX370102A TDMA IQproducer™
  • MX370104A Multi-carrier IQproducer™
  • MX370105A Mobile WiMAX™ IQproducer™
  • MX370106A DVB-T/H IQproducer™
  • MX370107A Fading IQproducer™
  • MX370108A LTE IQproducer™
  • MX370108A-001 LTE-Advanced FDD Option (Requires MX370108A)
  • MX370109A XG-PHS IQproducer™
  • MX370110A LTE TDD IQproducer™
  • MX370110A-001 LTE-Advanced TDD Option (Requires MX370110A) NEW
  • MX370111A WLAN IQproducer™
  • MX370111A-002 802.11ac (160MHz) Option (Requires MX370111A)
  • MX370112A TD-SCDMA IQproducer™

* Generated waveform patterns used with MG3710A. Licence (sold separately) required for main frame to output signal from MG3710A.

Waveform Pattern Archive of waveform patterns with typical parameter settings for each communications method. Parameters cannot be changed. Waveform patterns supplied with MG3710A as standard and optional waveform patterns available.
Standard waveform patterns (bundled free-of-charge with main frame):
  • LTE-FDD/TDD TM1.1 to 3.3, W-CDMA, GSM/EDGE, CDMA2000™ 1X, 1xEV-DO, PDC, PHS, AWGN, WLAN (IEEE802.11a/b/g), Digital Broadcast (ISDB-T/BS/CS/CATV), GPS, Bluetooth™
Optional Waveform Patterns (Sold Separately) [Model: MX3700xxA]:
  • MX370073A DFS Radar Pattern (TELEC and FCC DFS test pulse signal set)
  • MX370075A DFS(ETSI) Waveform Pattern (ETSI DFS test pulse signal set)
  • MX370084A ISDB-Tmm Waveform Pattern
Generation of Custom Waveform Pattern IQ sample data files (in ASCII format) programmed by using general EDA (Electronic Design Automation) tools such as MATLAB™ can also be converted to waveform patterns for MG3710A.

Options

Options Descriptions
Hardware
Main Frame
[1xx : retrofit]
MG3710A Vector Signal Generator
MG3710A-001 / 101 Rubidium Reference Oscillator
MG3710A-002 / 102 High Stability Reference Oscillator
MG3710A-011 / 111 2ndary HDD
MG3710A-017 / 117 Universal Input/Output
MG3710A-021 / 121 BER Test Function
MG3710A-029 OS Upgrade to Windows™ 7
MG3710A-313 Removable HDD
Hardware
1st RF (require one option)
MG3710A-032 1stRF 100 kHz to 2.7 GHz
MG3710A-034 1stRF 100 kHz to 4 GHz
MG3710A-036 1stRF 100 kHz to 6 GHz
Hardware
2nd RF (optional)
[1xx : retrofit]
MG3710A-062 / 162 2ndRF 100 kHz to 2.7 GHz
MG3710A-064 / 164 2ndRF 100 kHz to 4 GHz
MG3710A-066 / 166 2ndRF 100 kHz to 6 GHz
Hardware
1st RF Option
[1xx : retrofit]
MG3710A-018 / 118 Analog IQ Input/Output
MG3710A-041 / 141 High Power Extension for 1stRF
MG3710A-042 / 142 Low Power Extension for 1stRF
MG3710A-043 / 143 Reverse Power Protection for 1stRF
MG3710A-045 / 145 ARB Memory Upgrade 256 Msample for 1stRF
MG3710A-046 / 146 ARB Memory Upgrade 1024 Msample for 1stRF
MG3710A-048 / 148 Combination of Baseband Signal for 1stRF
MG3710A-049 / 149 AWGN for 1stRF
MG3710A-050 / 150 Additional Analog Modulation Input for 1st RF
Hardware
2nd RF Option
[1xx : retrofit]
MG3710A-071 / 171 High Power Extension for 2ndRF
MG3710A-072 / 172 Low Power Extension for 2ndRF
MG3710A-073 / 173 Reverse Power Protection for 2ndRF
MG3710A-075 / 175 ARB Memory Upgrade 256 Msample for 2ndRF
MG3710A-076 / 176 ARB Memory Upgrade 1024 Msample for 2ndRF
MG3710A-078 / 178 Combination of Baseband Signal for 2ndRF
MG3710A-079 / 179 AWGN for 2ndRF
MG3710A-080 / 180 Additional Analog Modulation Input for 2nd RF
Software
Waveform Pattern
MX370073A DFS Radar Pattern                        ....[For TELEC/FCC]
MX370075A DFS(ETSI) Waveform Pattern       ....[For ETSI]
MX370084A ISDB-Tmm Waveform Pattern
Software
IQproducer™
MX370101A HSDPA/HSUPA IQproducer™
MX370102A TDMA IQproducer™
MX370103A CDMA2000™ 1xEV-DO IQproducer™
MX370104A Multi-carrier IQproducer™
MX370105A Mobile WiMAX™ IQproducer™
MX370106A DVB-T/H IQproducer™
MX370107A Fading IQproducer™
MX370108A LTE IQproducer™
MX370108A-001 LTE-Advanced FDD Option        [Requires MX370108A]
MX370110A LTE TDD IQproducer™
MX370110A-001 LTE-Advanced TDD Option        [Requires MX370110A]
MX370111A WLAN IQproducer™
MX370111A-002 802.11ac (160MHz) Option        [Requires MX370111A]
MX370112A TD-SCDMA IQproducer™
Warranty Service MG3710A-ES2102 years Extended Warranty Service
MG3710A-ES3103 years Extended Warranty Service
MG3710A-ES5105 years Extended Warranty Service


Checking with Anritsu...    




Checking with Anritsu...    




Coming Soon..



Note: All trademarks that appear on this website are the property of their respective owners.


MG3740A


MG3740A MG3740A MG3740A
MG3740A
MG3740A
MG3740A
MG3740A

The MG3740A Analog Signal Generator has excellent RF specifications, including SSB Phase Noise, output level, etc., and versatile modulation functions (AM/FM/ΦM/Pulse). The MG3740A is the ideal solution for high-purity signal source for testing analog radio Rx characteristics. Moreover, adding the digital modulation option supports generation of narrowband digital modulation signals.

The MG3740A Analog Signal Generator can be expanded to add digital modulation signal generation functions, supporting evaluation of digital public safety radio systems.

Dual RF Output

mg3740a_dualrf

The dual RF outputs supporting wanted + interference waves for tests of Rx characteristics, evaluation of wireless and amplifier intermodulation characteristics, and output of RF/LO signals for mixer tests, cut test costs by eliminating the need for two signal generators.

Not only different frequencies but also different levels and modulations can be set independently at each SG while each is tracking the other.


mg3740a_dualwave

SSB Phase Noise Performance

mg3710a_SSB

< -140 dBc/Hz (nom.) @ 100 MHz, 20 kHz offset, CW
< -131 dBc/Hz (typ.) @ 1 GHz, 20 kHz offset, CW
< -125 dBc/Hz (typ.) @ 2 GHz, 20 kHz offset, CW

SSB phase noise is an important performance index for signal generators.

For example, when using a signal generator for the following purposes, it is important to pre-confirm that the signal generator performance satisfies the measurement specifications.

  • Communications with narrow bandwidth of several kHz
  • OFDM Signals with narrow subcarrier gap
  • CW interference waveforms

High Level Accuracy

mg3740a_accuracy

Absolute Level Accuracy: ±0.5 dB *1
Linearity: ±0.2 dB (typ.) *2

Excellent level accuracy and linearity are key factors with a large impact on measurement accuracy.


*1 400MHz to 3GHz, -110 to +10 dBm
*2 50 MHz to 3GHz, -110 to -1 dBm

Fast Switching Speed: < 600us (List/Sweep Mode)

The MG3740A supports high-speed switching in the sweep and list mode separately from normal remote control. It is ideal for production lines requiring short test times.

Sweep Mode

List Mode

In Sweep mode, the dwell time per point or number of points is split between the frequency range and level range (Start/Stop). This mode is used when matching dwell time per point and frequency / level steps.


In List mode, the frequency, level and dwell time can be set for each of up to 500 points. This mode is used when wanting to set any dwell time, and frequency / level step per point.


mg3740a_sweep
mg3740a_list

Low Power and High Power Output Extension

Assured Maximum Output Power Level (CW):

Frequency Range Standard Opt. 041 / 071
100 kHz to 10 MHz +5 dBm +5 dBm
10 MHz to 50 MHz +10 dBm +10 dBm
50 MHz to 400 MHz +13 dBm +20 dBm
400 MHz to 3GHz +23 dBm
3 GHz to 4GHz +20 dBm
4 GHz to 5GHz +13 dBm
5 GHz to 6 GHz +11 dBm +11 dBm
mg3740a_max_power

In conventional measurement setup, path loss is increased by the various external components in the RF path. Thus, an external amp is required when the output of the general signal source is insufficient.

The MG3740A High Power Extension option*1 improves signals required for path loss compensation. It eliminates the cost of an external amp, supports stable level accuracy measurements and reduces risk of damage to the DUT from the external amp.


Amplitude Setting Range:

Options Setting Range (dBm)
without
Reverse Power Protection*3
with
Reverse Power Protection*3
Standard -110 to +17 -110 to +17
with High Power Extension -110 to +30 -110 to +25
with Low Power Extension -144 to +17 -144 to +17
with Low and High Power Extension -144 to +30 -144 to +25

On the other hand, the MG3740A also supports a convenient option for extending the lower RF output limit via Low Power Extension*2 option when performing high-sensitivity Rx tests.

*1 High Power Extension for 1st RF / 2nd RF [Opt.041 / 071]
*2 Low Power Extension for 1st RF / 2nd RF [Opt.042 / 072]
*3 Reverse Power Protection for 1st RF / 2nd RF [Opt.043 / 073]

Expansion to Digital Modulation Signal Generator

Adding the digital modulation option adds a digital modulation signal generator function providing a cost-effective solution for testing public safety digital radio systems.

Digital Modulation [Opt. 020]


  • Digital Modulation Performance
    • RF Modulation Bandwidth : 2 MHz
    • Sampling Rate : 20 kHz to 8 MHz

  • Waveform generation software: IQproducer™ (License sold separately)
    • TDMA IQproducer™
    • Fading IQproducer™


Basic Performance

Parameters / Characteristics Specifications
Frequency Frequency Range 9 kHz to 2.7 GHz (MG3740A-032/062)
9 kHz to 4 GHz (MG3740A-034/064)
9 kHz to 6 GHz (MG3740A-036/066)
Resolution 0.01 Hz
Output Level Output Range Without reverse power protection
   -110 to +17 dBm (standard)
   -110 to +30 dBm (with high power extension option)
   -144 to +17 dBm (with low power extension option)
   144 to +30 dBm (with high power extension and low power extension option)
Resolution 0.01 dB
Accuracy CW, +18° to +28°C, , -100 to +5 dBm, without reverse power protection
   ±0.5 dB typ. (100 kHz ≤ f < 50 MHz)
   ±0.5 dB     (50 MHz ≤ f ≤ 3 GHz)
   ±0.7 dB     (3 GHz < f ≤ 4 GHz)
   ±0.8 dB     (4 GHz < f ≤ 6 GHz)
Signal Purity Spurious / Harmonics < -30 dBc
Spurious / Non-harmonics -30 dBm ≤ Output level ≤ +5 dBm, CW, &ge 10 kHz offset
   < -62 dBc, -70 dBc typ. (100 kHz ≤ f ≤ 187.5 MHz)
   < -68 dBc, -76 dBc typ. (187.5 MHz < f ≤ 750 MHz)
   < -62 dBc, -76 dBc typ. (750 MHz < f ≤ 1.5 GHz)
v< -56 dBc, -70 dBc typ. (1.5 GHz < f ≤ 3 GHz)
   < -50 dBc, -64 dBc typ. (3 GHz < f ≤ 6 GHz)
SSB Phase Noise CW, 20 kHz offset, Phase Noise Opt. < 200 kHz
   < -140 dBc/Hz nominal (100 MHz)
   < -131 dBc/Hz typ. (1 GHz)
   < -125 dBc/Hz typ. (2 GHz)
Dimensions and Mass 426 (W) x 177 (H) x 390 (D) mm (Exclusive surface projection)
≤13.7 kg (with Opt-032 or 034 or 036, excluding other options)
Remote Control Interface GPIB, 1000Base-T, USB-B

Options

Options Descriptions
Hardware
Main Frame
[1xx : retrofit]
MG3740A Analog Signal Generator
MG3740A-001 / 101 Rubidium Reference Oscillator
MG3740A-002 / 102 High Stability Reference Oscillator
MG3740A-011 / 111 2ndary HDD
MG3740A-017 / 117 Universal Input/Output
MG3740A-020 / 120 Digital Modulation
MG3740A-021 / 121 BER Test Function
MG3740A-029 OS Upgrade to Windows™ 7
MG3740A-313 Removable HDD
Hardware
1st RF (require one option)
MG3740A-032 1stRF 100 kHz to 2.7 GHz
MG3740A-034 1stRF 100 kHz to 4 GHz
MG3740A-036 1stRF 100 kHz to 6 GHz
Hardware
2nd RF (optional)
[1xx : retrofit]
MG3740A-062 / 162 2ndRF 100 kHz to 2.7 GHz
MG3740A-064 / 164 2ndRF 100 kHz to 4 GHz
MG3740A-066 / 166 2ndRF 100 kHz to 6 GHz
Hardware
1st RF Option
[1xx : retrofit]
MG3740A-041 / 141 High Power Extension for 1stRF
MG3740A-042 / 142 Low Power Extension for 1stRF
MG3740A-043 / 143 Reverse Power Protection for 1stRF
MG3740A-045 / 145 ARB Memory Upgrade 256 Msample for 1stRF *1
MG3740A-048 / 148 Combination of Baseband Signal for 1stRF *1
MG3740A-050 / 150 Additional Analog Modulation Input for 1st RF
Hardware
2nd RF Option
[1xx : retrofit]
MG3740A-071 / 171 High Power Extension for 2ndRF
MG3740A-072 / 172 Low Power Extension for 2ndRF
MG3740A-073 / 173 Reverse Power Protection for 2ndRF
MG3740A-075 / 175 ARB Memory Upgrade 256 Msample for 2ndRF *1
MG3740A-078 / 178 Combination of Baseband Signal for 2ndRF *1
MG3740A-080 / 180 Additional Analog Modulation Input for 2nd RF
Software
IQproducer™
MX370102A TDMA IQproducer™
MX370107A Fading IQproducer™
Warranty Service MG3740A-ES2102 years Extended Warranty Service
MG3740A-ES3103 years Extended Warranty Service
MG3740A-ES5105 years Extended Warranty Service

*1 : Requires MG3740A-020/120.



Checking with Anritsu...    




Checking with Anritsu...    




Coming Soon..



Note: All trademarks that appear on this website are the property of their respective owners.


MG3692C/ MG3694C/ MG3695C/ MG3697C


MG369xC MG369xC MG369xC
MG369xC
MG369xC
MG369xC

The MG369xC series of broadband signal generators covers Audio, HF, VHF, UHF, RF and microwave frequencies from 0.1 Hz to 70 GHz in single coaxial output and up to 500 GHz or beyond, with external multipliers. In addition, it is easy to operate either through intuitive front panel controls or remotely via GPIB or Ethernet connectivity.

The MG369xC replaces the existing MG369xB signal generator, offering three levels of best-in-class SSB phase noise performance; Standard, Ultra low phase noise (option 3) and Premium phase noise (option 3X).along with full suite of modulation capabilities for signal simulations from simple to the most complex. For IQ modulation, the IF input option allows the easy up-conversion of an externally IQ-modulated RF signal. The MG369xC preserves full backward compatibility with the MG369xA/B and previous 68C/69B series of RF and microwave signal generators.

The MG369xC is the "ideal microwave signal generator" because it offers unsurpassed frequency coverage, the lowest phase noise, leveled output power, spectral purity, switching speed, modulation performance, size, upgradeability, reliability, and service. This signal generator is configurable for a broad range of applications from R&D to manufacturing and depot repair.

Industry Best Broad Frequency Coverage

Two options are available to extend the 2 GHz low end frequency limit of the base models down to 8 MHz. Option 4 uses a digital down-converter (DDC) with successive divide-by-two circuitry. It offers the best phase noise performance of the two choices, at the expense of some analog performance < 500 MHz. In that range, analog sweep mode is not available, and pulse modulation performance is specified as typical. In addition, frequency and phase modulation mod index is scaled by the division ratio of each band of the DDC. Option 5 maintains all analog performance by using a heterodyne mixing down-converter, but does not improve phase noise performance.

If frequency coverage down to 0.1 Hz is desired, Option 22 can be added with either Option 4 or 5. Option 22 uses Direct Digital Synthesis (DDS) for CW and Step Sweep modes of operation. Modulation and analog sweep are not available in the DDS band. Frequency resolution < 10 MHz is 0.02 Hz. Output power across the complete instrument frequency range is degraded by 2 dB.

Industry Best Phase Noise

mg369xc_ssb

Phase noise is specified and guaranteed only with internal reference. In External Reference mode, the phase noise of the external supplied reference, and the selected external reference bandwidth, will dictate the instrument phase noise performance.

Phase noise is not degraded when adding high power Option 15. The MG369xC is ideal for LO substitution and clock generation applications.

Industry Best Pulse Modulation

Option 26 adds pulse modulation, driven externally via a rear panel BNC connector, TTL. For internal modulation, add Internal LF and Pulse Generators Option 27. Pulse modulation specifications apply at maximum rated power, unless otherwise noted. Pulse modulation is not available < 10 MHz with Option 22. With 100 ns leveled pulse widths, with 10 ns resolution along with the ability to generate, single, doublet, triplet and quadruplet pulses. The MG369xC is the most comprehensive emulation and test of high performance narrow pulse radars.


mg369xc_pulsemod

Full Analog Modulation

With internal and external AM, FM, Phase and Pulse modulation, the MG369xC is ideal for any type of analog signal emulation.

High Output Power

The High Output Power option eliminates the cost of an external amp, supports stable level accuracy measurements and reduces risk of damage to the DUT from the external amp.


mg369xc_maxpower

Basic Performance

Parameters / Characteristics Specifications
Frequency Frequency Range 0.1 Hz to 10 GHz (MG3691C-4-22)
0.1 Hz to 20 GHz (MG3692C-4-22)
0.1 Hz to 31.8 GHz (MG3693C-4-22)
0.1 Hz to 40 GHz (MG3694C-4-22)
0.1 Hz to 50 GHz (MG3695C-4-22)
0.1 Hz to 67 GHz (MG3697C-4-22)
Resolution 0.01 Hz
Output Level Standard Output Range With Option 4 or 5 (down to 8 MHz coverage), with mechanical attenuator
   -115 to +19 dBm (MG3691C > 8 MHz < 10 GHz)

   -115 to +19 dBm (MG3692C > 8 MHz ≤ 10 GHz)
   -115 to +19 dBm (MG3692C > 10 GHz ≤ 20 GHz)

   -115 to +15 dBm (MG3693C > 8 MHz ≤ 10 GHz)
   -115 to +12 dBm (MG3693C > 10 GHz ≤ 20 GHz)
   -115 to +12 dBm (MG3693C > 20 GHz ≤ 31.8 GHz)

   -115 to +15 dBm (MG3694C > 8 MHz ≤ 10 GHz)
   -115 to +12 dBm (MG3694C > 10 GHz ≤ 20 GHz)
   -115 to +9 dBm (MG3694C > 20 GHz ≤ 40 GHz)

   -105 to +12 dBm (MG3695C > 8 MHz ≤ 2.2 GHz)
   -105 to +10 dBm (MG3695C > 2.2 GHz ≤ 20 GHz)
   -105 to +6 dBm (MG3695C > 20 GHz ≤ 40 GHz)
   -105 to +3 dBm (MG3695C > 40 GHz ≤ 50 GHz)

   -105 to +12 dBm (MG3697C > 8 MHz ≤ 2.2 GHz)
   -105 to +10 dBm (MG3697C > 2.2 GHz ≤ 20 GHz)
   -105 to +6 dBm (MG3697C > 20 GHz ≤ 40 GHz)
   -105 to +3 dBm (MG3697C > 40 GHz ≤ 67 GHz)

For output power with Option 22, 0.1 Hz to 10 MHz coverage, derate all specifications by 2 dB

High Power Output Range
(with Option 15), with mechanical attenuator
With Option 4 or 5 (down to 8 MHz coverage)
   -115 to +19 dBm (MG3691C > 8 MHz < 2.2 GHz )
   -115 to +25 dBm (MG3691C > 2.2 GHz ≤ 20 GHz)

   -115 to +19 dBm (MG3692C > 8 MHz < 2.2 GHz )
   -115 to +25 dBm (MG3692C > 2 GHz ≤ 10 GHz)
   -115 to +22 dBm (MG3692C > 10 GHz ≤ 16 GHz)
   -115 to +21 dBm (MG3692C > 16 GHz ≤ 20 GHz)

   -115 to +17 dBm (MG3693C > 8 MHz ≤ 2.2 GHz)
   -115 to +21 dBm (MG3693C > 2.2 GHz ≤ 20 GHz)
   -115 to +17 dBm (MG3693C > 20 GHz ≤ 31.8 GHz)

   -115 to +17 dBm (MG3694C > 8 MHz ≤ 2.2 GHz)
   -115 to +21 dBm (MG3694C > 2.2 GHz ≤ 20 GHz)
   -115 to +17 dBm (MG3694C > 20 GHz ≤ 40 GHz)

   -105 to +16 dBm (MG3695C > 8 MHz ≤ 2.2 GHz)
   -105 to +21 dBm (MG3695C > 2.2 GHz ≤ 20 GHz)
   -105 to +17 dBm (MG3695C > 20 GHz ≤ 40 GHz)
   -105 to +11 dBm (MG3695C > 40 GHz ≤ 50 GHz)

   -105 to +16 dBm (MG3697C > 8 MHz ≤ 2.2 GHz)
   -105 to +19 dBm (MG3697C > 2.2 GHz ≤ 20 GHz)
   -105 to +16 dBm (MG36997C > 20 GHz ≤ 40 GHz)
   -105 to +9 dBm (MG3697C > 40 GHz ≤ 67 GHz)
   -105 to +3 dBm typical (MG3697C > 67 GHz ≤ 70 GHz)

Without Option 4 and 5
   -115 to +26 dBm (MG3691C ≥ 2 GHz ≤ 10 GHz)

   -115 to +26 dBm (MG3692C ≥ 2 GHz ≤ 10 GHz)
   -115 to +25 dBm (MG3692C > 10 GHz ≤ 16 GHz)
   -115 to +23 dBm (MG3692C > 16 GHz ≤ 20 GHz)

   -115 to +23 dBm (MG3693C ≥ 2 GHz ≤ 20 GHz)
   -115 to +19 dBm (MG3693C > 20 GHz ≤ 31.8 GHz)

   -115 to +23 dBm (MG3694C ≥ 2 GHz ≤ 20 GHz)
   -115 to +19 dBm (MG3694C > 20 GHz ≤ 40 GHz)

   -105 to +23 dBm (MG3695C ≥ 2 GHz ≤ 20 GHz)
   -105 to +19 dBm (MG3695C > 20 GHz ≤ 40 GHz)
   -105 to +13 dBm (MG3695C > 40 GHz ≤ 50 GHz)

   -105 to +21 dBm (MG3697C ≥ 2 GHz ≤ 20 GHz)
   -105 to +19 dBm (MG36997C > 20 GHz ≤ 40 GHz)
   -105 to +9 dBm (MG3697C > 40 GHz ≤ 67 GHz)
   -105 to +3 dBm typical (MG3697C > 67 GHz ≤ 70 GHz)

For output power with Option 22, 0.1 Hz to 10 MHz coverage, derate all specifications by 2 dB

Resolution 0.01 dB or 0.001 mV
Accuracy and Flatness CW, +25 ± 10°C, Attenuation < 25 dB
   ±1.0 dB typ. (> 20 MHz ≤ 40 GHz)
   ±1.5 dB typ. (> 20 MHz ≤ 40 GHz, with high power option 15)
   ±1.5 dB typ. (> 40 MHz ≤ 67 GHz)
Signal Purity Spurious / Harmonics Output level < +10 dBm
   < -30 dBc typ. (0.1 Hz < f ≤ 10 MHz) with Option 22
   < -40 dBc typ. (10 MHz < f ≤ 2.2 GHz) with Option 4
   < -30 dBc typ. (10 MHz < f ≤ 2 GHz) with Option 5
   < -60 dBc typ. (2 GHz < f ≤ 20 GHz)    < -40 dBc typ. (20 GHz < f ≤ 40 GHz)    < -60 dBc typ. (40 GHz < f ≤ 50 GHz) MG3695C only    < -60 dBc typ. (40 GHz < f ≤ 67 GHz) MG3697C only
Spurious / Non-harmonics Output level < +10 dBm
   < -30 dBc typ. (0.1 Hz < f ≤ 10 MHz) with Option 22
   < -60 dBc typ. (10 MHz < f ≤ 2.2 GHz) with Option 4
   < -40 dBc typ. (10 MHz < f ≤ 2 GHz) with Option 5
   < -60 dBc typ. (2 GHz < f ≤ 67 GHz)
SSB Phase Noise CW, 10 kHz offset
   < -139 dBc/Hz typ. (0.1 Hz < f < 10 MHz)
   < -116 dBc/Hz typ. (10 MHz < f < 2.2 GHz) with Option 4
   < -110 dBc/Hz typ. (10 MHz < f < 2 GHz) with Option 5
   < -109 dBc/Hz typ. (2 GHz < f < 10 GHz)
   < -103 dBc/Hz typ. (10 GHz < f < 20 GHz)
   < -100 dBc/Hz typ. (20 GHz < f < 40 GHz)
   < -94 dBc/Hz typ. (40 GHz < f < 67 GHz)
Dimensions and Mass 429 (W) x 133 (H) x 450 (D) mm (Exclusive surface projection)
≤18 kg
Remote Control Interface GPIB, 10/100Base-T

Options

Options Descriptions
Basic Hardware MG3692C Signal Generator, 2 GHz to 20 GHz
MG3694C Signal Generator, 2 GHz to 40 GHz
MG3695C Signal Generator, 2 GHz to 50 GHz
MG3697C Signal Generator, 2 GHz to 67 GHz (operational to 70 GHz)
Optional MG3690C-1A Rack Mount with slides
MG3690C-1B Rack Mount without slides
MG3690C-2x Mechanical Step Attenuator
MG3690C-3 Ultra Low Phase Noise, improved Standard Phase Noise
MG3690C-3X Premium Phase Noise - improves option 3 (< 1 kHz offset)/td>
MG3690C-4 Extends Frequency Coverage from 8 MHz to 2.2 GHz
MG3690C-5 Extends Frequency Coverage from 8 MHz to 2 GHz
MG3690C-6 Analog Sweep Capability
MG3690C-7 IF Up-Conversion
MG3690C-8 Power Monitor
MG3690C-9X Rear Panel Output
MG3690C-10 User-defined Modulation Waveform Software
MG3690C-12 Frequency and Phase
MG3690C-14 Amplitude Modulation
MG3690C-15x High Power
MG3690C-16 High Stability Time Base
MG3690C-17 Delete Front Panel
MG3690C-18 DC Output: + 15 VDC, 1A (nominal)
MG3690C-20 Scan Modulation
MG3690C-22 Extends Frequency Coverage from 0.1 Hz to 10 MHz
MG3690C-26x Pulse Modulation
MG3690C-27 Internal LF and Pulse Generators
MG3690C-28x Analog Modulation Suite
MG3690C-36 Ultra-Stable Phase Tracking
Warranty Standard 3 Years Warranty Service

x - Option designation varies with MG3690C model.



Checking with Anritsu...    




Checking with Anritsu...    




Coming Soon..



Note: All trademarks that appear on this website are the property of their respective owners.